Lean to 14×14 Pavilion Plans – Free DIY Plans

If you want to learn more about lean to 14×14 pavilion plans you have to take a close look over the free plans in the article. This pavilion is built on a 6×6 structure and it features a lean to roof with a very elegant design. This outdoor shelter makes for the perfect relaxation area on your patio. This also makes for a hot tub pavilion. Remember to read the local codes before starting the project and to comply with the local regulations. The codes differ from one area to another, so it is safer to read them thoroughly.

If you want to get the job done in a professional manner, we recommend you to plan everything with attention, as to prevent costly mistakes and to build a professional garden project. Invest in high quality materials, such as cedar, pine or redwood, as the bench will be exposed to all kinds of weather. Apply a few coats of paint over the components, to enhance their appearance and to protect them from bad weather.

Made from this plan

 

Lean to 14×14 Pavilion Plans – Free DIY Plans

Building-a-14×14-pavilion

Materials

• 1 – 4 pieces of 6×6 lumber – 8 ft long POSTS
• 2 – 3 pieces of 6×6 lumber – 14 ft long, 1 piece – 16 ft SUPPORT BEAMS
• 3 – 2 pieces of 6×6 lumber – 36 1/2″ long, 1 piece – 16 ft RIDGE BEAMS
• 4 – 10 pieces of 6×6 lumber – 48″ long BRACES
• 5 – 9 piece of 2×6 lumber – 190 1/2″ long RAFTERS
• 6 – 13 pieces of 1×4 lumber – 16long PURLINS
• 7 – 2 pieces of 1×8 lumber – 190 1/2″ long, 4 pieces – 96 3/4″ long TRIMS
• 8 – 6 pieces of 3’x8′ roofing, 6 pieces of 3’x10′ roofing ROOFING

• 10 pieces of 6×6 lumber – 8 ft
• 3 pieces of 6×6 lumber – 14 ft
• 2 pieces of 6×6 lumber – 16 ft
• 9 pieces of 2×6 lumber – 16 ft
• 13 pieces of 1×4 lumber – 16 ft
• 2 pieces of 1×8 lumber – 16 ft
• 4 pieces of 1×8 lumber – 10 ft
• 6 pieces of 3’x8′ roofing, 6 pieces of 3’x10′ roofing
• 4 L strong tie
• 2 post to beam connectors
• 16 pieces of 7″ screws
• 4 post anchors
• 250 pieces 1 5/8″ screws
• 50 pieces 5 1/2″ screws
• 1 1/2″ structural screws
• 2″ nails
• wood glue, stain/paint
• rafter ties

Tools

• Hammer, Tape measure, Carpentry square
• Miter saw, Drill machinery, Screwdriver, Sander, Router
• Safety Gloves, Safety Glasses, Respiratory Mask

Time

• One week

Lean to 14×14 Pavilion Plans – Cut List

Cut-List—14×14-lean-to-pavilion

STEP 1: Building the base of the carport

Laying-out-the-pavilion-posts

The first step of the garden project is to select the location for the lean to pavilion. Make sure the ground is level and then layout the 6×6 posts with batter boards and string. Measure the diagonals and apply the 3-4-5 rule to the corners, to make sure the corners are square.

Fitting the posts into concrete

You can set the posts into place with several methods. First of all, you can attach the posts to an already existing concrete slab using metal anchors. Alternatively, you can dig 2-3′ deep holes and pour concrete footing in which you set post anchors. Last but not least, you can dig the holes and set the posts directly into concrete.

For this project, we will assume you will use metal anchors. Use a spirit level to plumb the posts vertically and use temporarily braces to lock them, until you build the roof for the structure.

Top-rails

Use 6×6 lumber for the top plates. As you can see in the plans, you need to make notches to the plates. Use a circular saw to make parallel cuts and then remove the excess with a chisel.

Fitting-the-top-rails

Fit the plates to the top of the pavilion. Make sure the posts are perfectly plumb and then check if the corners are square. Drill pilot holes and insert 7″ screws to lock everything into place tightly.

Fitting-the-ridge-beam

Next, attach the 6×6 supports to one side of the pavilion. Plumb the posts with a spirit level and secure it to the plates with 2 L strong ties and 1 1/2″ structural screws. Center the 6×6 ridge beam to the supports, making sure the side overhangs are 12″. Use post to beam connectors to secure the beam to the supports. Make sure the corners are square and align the edges flush.

Fitting-the-braces

Use 6×6 lumber for the braces. Use a miter or circular saw to make the 45 degree cuts at both ends. Fit the braces to the posts of the carport and then lock them into place with 5 1/2″ screws. Drill pilot holes before inserting the screws, to prevent the wood from splitting.

STEP 2: Building the roof of the lean to carport

Rafters-for-lean-to-pavilion

Rafters

Use 2×6 lumber for the rafters of the large pavilion. Mark the cut lines on the beams and then get the job done with a circular saw. Smooth the edges with attention.

Fitting-the-rafters

Fit the rafters to the top of the carport, every 24″ on center. Double the rafters that are placed at both ends of the carport. Use rafter ties and 1 1/2″ structural screws to lock the beams to the top plates of the carport.

Fitting-the-purlins

Fit the 1×4 purlins to the top of the pavilion, starting with the bottom up to the top. Use 1 5/8″ screws to secure the purlins into place.

Fitting-the-front-and-back-roof-trims

Fit the 1×8 trims to the front and back of the pavilion. Align the edges flush and insert 2″ nails to lock them to the rafters.

Side-roof-trims

Fit the 1×8 trims to the sides of the lean to pavilion. Align the edges and insert 2″ nails to secure the trims into place.

Fitting-the-roofing

Attach the metal roofing sheets to the pavilion. Use appropriate 3/4″ screws to secure the sheets to the purlins. Install the drip edges to enhance the look of the pavilion and to seal the structure. I also have nice plans for a 12×16 lean to pavilion. Therefore, I recommend you to take a look over the rest of my designs.

14×14-pavilion-plans—side-view

Last but not least, you need to take care of the finishing touches. Fill the gaps with wood putty and smooth the surface with 120-220 grit sandpaper. Apply a few coats of paint or stain to protect the shed components from the elements and to enhance the look of the project.

How-to-build-a-14×14-pavilion

Make sure you take a look over my other pavilion plans here.

This diy project was about large lean to pavilion plans 14×4. If you have enjoyed the free project, I recommend you to share it with your friends, by using the social media widgets. You can always save the plans as PDF or Print them using the floating widget on the left side of the screen (working only on PC or laptop).